How to remove chain link fence

Whether upgrading to a new fence or simply replacing your current one, removing a chain link fence is a relatively easy process – providing you take the right steps. That said, the task can be quite laborious, so make sure you get some help with the removal to make the job that bit easier.
If you don’t plan to install another fence or dig the ground where the fence was located, you can simply cut off the posts just below ground level using a reciprocating saw with a metal-cutting blade. Offer the used chain link fencing to a neighbor who can make use of the fencing so you can avoid disposal costs.
The steps to move a chain link fence are as follows:
  1. Inspect the Chain Link Fence Posts. Depending on how the fence was previously installed, the fence posts may or may not be reusable.
  2. Mark Out the New Fence Line.
  3. Disassemble the Fence.
  4. Dig Out the Old Posts.
  5. Set the Fence Posts.
  6. Rebuild the Fence.
Install tension wire on the bottom of the fence line. This wire reinforces the bottom of a chain link fence and helps prevent the bottom from ‘pulling’ up if an animal tries to push the fabric out and away from the fence line.
Traditionally, chain link fences are held in place by buried posts surrounded in concrete. However, it is possible to install a chain link fence without concrete. With a hole that is the proper size, either gravel or a polymer backfill can keep fence posts in place for many years.
Dig 6-inches to 8-inches for end and corner posts. Dig 4-inches to 6-inches for line posts. Make the holes a third of the length of the pole length plus 4-inches for gravel. Fill all the holes with 4-inches of gravel.
Average Chain-Link Cost Per Foot
Linear Feet 4-foot Tall 6-foot Tall
50 $600 $750
100 $1,200 $1,500
150 $1,800 $2,250
200 $2,400 $3,000

How do you pound a chain link fence post?

Self-installed chain link fences are prone to a whole host of problems, including: Uneven alignment or spacing – the top rail shouldn’t slope even if your yard does, hinges should line up evenly with each other, and the gaps between posts should be identical.
If you decide to install your chain link fence without concrete, use a post-hole digger to make a hole deep enough to bury the posts at least two feet, or about 1/3rd of the height. Never pound the posts into the ground, especially if you have hard clay or rocky soil, because you’ll bend the tops.

Is 2 feet deep enough for fence posts?

The minimum depth that you should dig your fence post holes for panel sections is 2 feet. A general formula is to dig the holes one-third to one-half of the post’s aboveground height. The deeper you dig the holes, the more stability your fence has, but you must also purchase longer posts.
Chain Link vs Wood Fence

Even with their separate components – including metal stakes, galvanized posts, brackets and tie wires – chain link fences are almost always cheaper to purchase and install than wood, regardless of the type of lumber in consideration.

How many bags of concrete do I need for a chain link fence post?

A 40-pound bag of concrete mix makes 0.3 cubic feet, 60-pound bags make 0.45 cubic feet and 80-pound bags make 0.6 cubic feet. For the example given, 56 of the 40-pound bags, 37 of the 60-pound bags or 28 of the 80-pound bags will be needed for the fence installation.

How do I put a post in the ground without concrete?

What is the best concrete mix for fence posts?

In terms of the ratio to use for a concreting fence posts, the best mix is a mix of 1:2:4 (1 cement, 2 sand, 4 aggregate). Concrete is always best mixed using a cement mixer to ensure it’s even, but if you only need to mix a little, hand mixing is ok (see mixing concrete project above for tips on how to do this).

Can you use normal concrete for fence posts?

3 Answers. If the setting time is not an issue, you can certainly use normal quickcrete – or save even more money by purchasing cement and aggregate (sand/gravel/rock) and really making use of the mixer. Standard concrete mixing practice is to mix the dry materials and then add water.

How do I make sure my fence posts are straight?

  1. Step 1: Clear the Fence Line. Remove any vegetation in the path of the fence.
  2. Step 2: Mark the Corners.
  3. Step 3: Make Batter Boards.
  4. Step 4: Align the First Batter Board.
  5. Step 5: Square the Corners.
  6. Step 6: Set Stakes to Mark Posts.
  7. Step 7: Align Posts with the String or Laser.

How do I stop my fence post from rotting?

How do you waterproof a fence post?

Pour waterproofing wood sealant into a bucket and immerse the end of the wood fence post that will be buried below ground into the sealant. Allow the post to remain in the sealant overnight. According to We Build Fences, untreated wood posts buried below ground have shorter lifespans because of rot.
You May Also Like