How do you start a Stihl ms170 chainsaw?
What is the proper way to start a Stihl chainsaw?
Step 1 of 15: Before starting your chain saw, the chain brake should be activated by pushing it forward (see picture). Step 2 of 15: Always remove the bar cover before starting your chain saw. Step 3 of 15: If your chain saw is fitted with a decompression valve, press it now.
Why is it hard to start my Stihl chainsaw?
Problems starting a Stihl chain saw can be related to gasoline storage, spark plugs, and incorrect starting procedures.
How do you cold start a Stihl chainsaw?
How do you start a Stihl flooded chainsaw?
Pull the starting rope five or six times to clear fuel out of the combustion chamber. Replace the air filter and spark plug, and connect the spark plug wire. Leave the choke open and pull the starting cord several times. The chain saw should start.
How does Stihl easy start?
The even pull on the starter rope overcomes the engine’s compression to minimize the strength and effort required to start. Stresses caused by quick, uneven movements are avoided. The spring automatically releases the stored energy to the crankshaft, starts it moving and ensures that the engine will start reliably.
How do you start a chainsaw that won’t start?
To solve this problem, open the spark plug hole with it facing away from you to drain all the fuel in the tank. Deactivate the choke by pushing in the control then pull the starter cord 6-8 times as you press in the throttle control. Dry off the spark plug and refit it back in place.
How do you start a Stihl chainsaw without a primer bulb?
Do Stihl chainsaws have a primer?
To one side of your Stihl chainsaw, you’ll find a small, translucent plastic bubble. This is the primer bulb and is used to remove air from the fuel pipe, so that it can flow to the carburetor. Press it a few times, it helps the engine start quicker.
Why is it so hard to start my chainsaw?
Old fuel collects moisture, making the fuel difficult to ignite. … It’s possible the engine is flooded with fuel. To clear excess fuel from the carburetor, place the choke lever in the Off position, hold the throttle trigger fully open and pull the starter rope 5 or 6 times. Try to start the chainsaw.
What do you do if you flood a Stihl chainsaw?
How do you start a chainsaw after sitting?
So how can you fix it?
- Just let the saw sit for 30 min and the excess gas will evaporate.
- Remove the spark plug, dry it, crank over the engine a few times to dry the cylinder. Now refit the plug and try again.
- Set the switch to “On”, set throttle to fully open, set choke to “Off” and crank over the engine.
How do I start my chainsaw?
Can you use starter fluid to start a chainsaw?
Another thing you can try if your chainsaw won’t start without starting fluid is replacing the air filter. If you have used starter fluid, then you know that you have to put the starter fluid into the air intake.
How do you start a 2 stroke chainsaw?
Should I start chainsaw with brake on or off?
Check the Chain Brake
When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
How do I keep my chainsaw running?
How to Keep your Chainsaw Running Like a Champ
- Keep your Chain Sharp: Keeping your chain sharp is probably the easiest and most effective way to extend the life of your saw. …
- Flip your Bar: …
- Drain your Gas: …
- Check your Sprocket: …
- Keep a watchful Eye:
How do you start a high compression chainsaw?
A Measure of Pressure
Unscrew the spark plug using a ratchet and screw the compression gauge in its place. Sometimes an adapter is needed to make a tight fit between the gauge and the chainsaw. Pull the starter rope a few times until the gauge stops moving. When it settles onto a number, you have an accurate reading.
Do you start a Stihl chainsaw with the brake on?
On a gas-powered Stihl chainsaw, the chain brake is located just in front of the handlebar. All you have to do to activate it is push it forward. This will keep the chain locked as a safety precaution while you are starting the chainsaw, and until you are ready to use the tool. Remove the bar cover.