How do you start a Homelite chainsaw?
Pull the choke lever, located underneath the ignition switch, all the way out. Pull the starter cord three times to get the engine revving. Push the choke lever to the “run” position, and squeeze the trigger on the rear handle with your right hand to start the chainsaw.
What is the fuel mixture for a Homelite chainsaw?
50-to-1
The recommended 50-to-1 fuel mixture includes 2.6 ounces of a high-quality, two-cycle oil with added fuel stabilizers and 1 gallon of unleaded 87-octane gas. Homelite recommends using their brand of oils, specifically designed to work in any model with a 50-to-1 fuel ratio.
What size chain does a Homelite 240 chainsaw take?
18″ Semi Chisel Saw Chain for Homelite Super 240 Chainsaws – (18 inch, 0.325″ Pitch, 0.050″ Gauge, 72 Drive Links, CSC-H72)
Why does my Homelite chainsaw wont stay running?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. … This sticky fuel can clog up the fuel filter and cause the engine to stall. If old fuel was left in the chainsaw, drain the old fuel from the fuel tank and replace the fuel filter.
What kind of spark plug do I need for a Homelite chainsaw?
Champion RCJ4 Spark Plug
Homelite Chainsaw Replacement (2 Pack) Champion RCJ4 Spark Plug # 870170001-2PK.
Are Homelite chainsaws any good?
The Homelite brand has a reputation for delivering affordable, functional tools with average homeowners in mind. This is on full display with the Homelite UT43122B electric chainsaw. It’s a good choice for occasional use and can handle pretty much any cutting job that’s likely to pop up around the yard.
How do you troubleshoot a Homelite chainsaw?
Basic Checks
- Make sure the chain moves freely around the bar. …
- Remove any old, stale gasoline from the gas tank if it has been sitting in the chainsaw for more than a week. …
- Refill the tank with fresh gas. …
- Ensure the starter is pushed to the right setting. …
- Remove and clean the air filter.
How do you adjust the carburetor on a Homelite chainsaw?
Why does my chainsaw stall when I give it gas?
Carburetor Adjustment
An engine stalls when it’s getting too much or not enough fuel from the carburetor. Stihl chainsaw carburetors usually have three adjustment screws: one each for idle, low speed and high speed. If the saw stalls while it’s idling, adjusting the idle screw, which usually is marked LA, should help.
Where is the spark plug located on a Homelite chainsaw?
How do I clean the carburetor on my Homelite chainsaw?
How do you clean a chainsaw carburetor?
Why will my chainsaw not start?
Where is the model number on a Homelite chainsaw?
Homelite Model and Serial Number Locations
Homelite chainsaws typically have the model number plate located on the rear handle.
How do you change the primer bulb on a Homelite chainsaw?
How do you start a chainsaw after sitting?
So how can you fix it?
- Just let the saw sit for 30 min and the excess gas will evaporate.
- Remove the spark plug, dry it, crank over the engine a few times to dry the cylinder. Now refit the plug and try again.
- Set the switch to “On”, set throttle to fully open, set choke to “Off” and crank over the engine.
How do you start a chainsaw?
How do you start a flooded chain saw?
Pull the starting rope five or six times to clear fuel out of the combustion chamber. Replace the air filter and spark plug, and connect the spark plug wire. Leave the choke open and pull the starting cord several times. The chain saw should start.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
Why won’t my chainsaw start when it’s hot?
When your chainsaw quits after it gets hot, you either have a problem with gas flow being restricted into the engine or with the spark. This is a common occurrence on older-model chainsaws. By replacing your spark plugs and keeping your gas lines clear you can reduce the chances of this problem recurring.